Posts Tagged ‘interface’
To pass the BSCI exam and become a CCNP, you have to be aware of the proper use of passive interfaces. You learned about passive interfaces in your CCNA studies, but here we’ll review the basic concept and clear up one misconception regarding passive interfaces and OSPF.
Configuring an interface as passive will still allow the interface to receive routing updates, but the interface will no longer transmit them. While the command itself would make you think this command will be applied at the interface level, that is not the case. Below, we’ll configure ethernet0 as a RIP passive interface.
R1(config)#router rip
R1(config-router)#passive-interface ethernet0
Ethernet0 will no longer send RIP routing updates, but will accept them.
The passive interface concept is clear enough with RIP, IGRP, and EIGRP – all protocols that send routing update packets. But OSPF doesn’t send routing update packets – OSPF sends link state advertisements. It’s the inability of the passive interface command to stop LSAs that lead many to think that passive interfaces cannot be used with OSPF. Read the rest of this entry »
When you earned your CCNA, you thought you learned everything there is to know about RIP. Close, but not quite! There are some additional details you need to know to pass the BSCI exam and get one step closer to the CCNP exam, and one of those involves RIP update packet authentication.
You’re familiar with some advantages of using RIPv2 over RIPv1, support for VLSM chief among them. But one advantage that you’re not introduced to in your CCNA studies is the ability to configure routing update packet authentication.
You have two options, clear text and MD5. Clear text is just that – a clear text password that is visible by anyone who can pick a packet off the wire. If you’re going to go to the trouble of configuring update authentication, you should use MD5. The MD stands for “Message Digest”, and this is the algorithm that produces the hash value for the password that will be contained in the update packets.
Not only must the routers agree on the password, they must agree on the authentication method. If one router sends an MD5-hashed password to another router that is configured for clear-text authentication, the update will not be accepted. debug ip rip is a great command for troubleshooting authenticated updates.
R1, R2, and R3 are running RIP over a frame relay cloud. Here is how RIP authentication would be configured on these three routers.
R1#conf t
R1(config)#key chain RIP
< The key chain can have any name. >
R1(config-keychain)#key 1
< Key chains can have multiple keys. Number them carefully when using multiples. >
R1(config-keychain-key)#key-string CISCO
< This is the text string the key will use for authentication. >
R1(config)#int s0
R1(config-if)#ip rip authentication mode text
< The interface will use clear-text mode. >
Read the rest of this entry »
As a CCNP candidate, as a CCNA, and in getting ready to pass the BSCI exam, you may be tempted to breeze through your static route studies, or even skip them! That’s because static routes are easy enough to configure, and as long as you remember the syntax of the ip route command, you’re in good shape.
But there’s one vital detail regarding static routes that many exam candidates miss. That’s because many CCNA and CCNP books say “the administrative distance of a static route is 1″, but that is not quite accurate.
You know from your CCNA studies that the ip route command is used to create a static route, and that you have the option of configuring a local exit interface or a next-hop IP address at the end of the command. However, the administrative distances are not the same. The AD of a static route that uses a local exit interface is zero! (That’s because the router considers a static route with a local exit interface to actually be a directly connected network.) The AD of a static route with a next-hop IP address is 1.
Therefore, if the router has the following two ip route statements to consider…
Read the rest of this entry »
For CCNA exam success, you had better know what split horizon is, how to turn it off, and when to turn it off. Knowing when to turn split horizon off is also important in production networks, because it can cause a hub-and-spoke network to have incomplete routing tables on the spokes.
Split horizon exists for a very good reason – routing loop prevention. The rule of split horizon states that a router cannot send an advertisement for a route out the same interface that it came in on. Split horizon is on by default on all interfaces running RIP, IGRP, and EIGRP.
In this CCNA tutorial, R1 will serve, as the hub and R2 and R3 will be the spokes. We’ll first configure EIGRP over the 172.16.123.0 /24 network, the network connecting the three routers.
R1#conf t
R1(config)#router eigrp 100
R1(config-router)#no auto-summary
R1(config-router)#network 172.12.123.0 0.0.0.255
R2#conf t
R2(config)#router eigrp 100
R2(config-router)#no auto-summary
R2(config-router)#network 172.12.123.0 0.0.0.255
R3#conf t
R3(config)#router eigrp 100
R3(config-router)#no auto-summary
R3(config-router)#network 172.12.123.0 0.0.0.255
Running show ip eigrp neighbor on R1 shows that adjacencies to R2 and R3 are up.
R1#show ip eigrp neighbor
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq Type
(sec) (ms) Cnt Num
1 172.12.123.3 Se0/0 11 00:02:45 1 5000 0 1
0 172.12.123.2 Se0/0 161 00:03:01 1 5000 0 1
Each router will now advertise its loopback address via EIGRP.
R1#conf t
R1(config)#router eigrp 100
R1(config-router)#network 1.1.1.0 0.0.0.255
R2#conf t
R2(config)#router eigrp 100
R2(config-router)#network 2.2.2.0 0.0.0.255
R3#conf t
R3(config)#router eigrp 100
R3(config-router)#network 3.3.3.0 0.0.0.255
Running show ip eigrp route on each router shows that R1 has a route for both R2’s and R3’s loopback. R2 and R3 will only see R1’s loopback address, and not each other’s. Why?
R1#show ip route eigrp
2.0.0.0/24 is subnetted, 1 subnets
D 2.2.2.0 [90/2297856] via 172.12.123.2, 00:03:19, Serial0/0
3.0.0.0/24 is subnetted, 1 subnets
D 3.3.3.0 [90/2297856] via 172.12.123.3, 00:03:04, Serial0/0
R2#show ip route eigrp
1.0.0.0/24 is subnetted, 1 subnets
D 1.1.1.0 [90/2297856] via 172.12.123.1, 00:03:40, Serial0/0.123
R3#show ip route eigrp
1.0.0.0/24 is subnetted, 1 subnets
D 1.1.1.0 [90/2297856] via 172.12.123.1, 00:05:17, Serial0/0.31
Read the rest of this entry »